PROTECT AND EXTEND THE LIFE OF YOUR ROOF WITH A ROOF MAINTENANCE SYSTEM.

Don’t replace your roof…restore it with one of our all-in-one Topps maintenance systems.

Why replace 100% of your roof when only 10% is the problem? Roof replacement is disruptive, costly and often completely unnecessary. The Topps® restoration and maintenance system is non-invasive, economical, adds years to the life of your existing roof and typically saves 1/2 to 2/3 the cost of premature replacement.

Topps commercial roofing systems blanket your commercial roof with a seamless, cold-applied rubber membrane that conforms to all surfaces, sealing out the damaging effects of weather and environmental corrosives. They are lightweight, sound deadening, energy efficient and, best of all, there’s NO downtime during application.

RubberClad™

RubberClad™ combines all of the ingredients of Topps Seal® Base Coat to lock out moisture and lock in PolyCore™ reinforcing membrane as System 5100 is installed across sloped built-up and concrete roofing. This most economical blend combines ingredients to take advantage of the properties added by the PolyCore center and builds sufficient mil thickness at the lowest cost possible. Its maximized adhesive package produces the tight bond to the original roof which characterizes a System 5100 completed roof overlay, utilizing the existing roof as its base and eliminating costly unnecessary tear-off and replacement.

RustArrestor™ [for Metal Roofs]

A package of two powerful cleaners simultaneously neutralize and dissolve surface rust as it stabilizes oxidation for coating with Topps Seal® water-free coatings. Applies by pump-up sprayer or rag mop at approximately 0.15 liters per square meter, followed by power wash after just 10 minutes. May be repeated if needed for heavy rust. In cases of heavier rust, allow to sit up to 30 minutes prior to power washing.

ClearSeal™ [for Asbestos & Concrete Roofs]

This penetrating clear thin primer prepares porous non-painted masonry and concrete for sealing with Topps Seal® and other coatings. ClearSeal absorbs and bonds light surface oxidation and forms an initial seal beneath the surface. Prepares oxidized surfaces so they may be coated over with excellent adhesion.

Bondit™ [for Bitumen Roofs]

Bondit allows for instant compatibility of Topps Seal® solvent based products over stable black bituminous systems for resurfacing them with rubber durability and the Topps Seal Energy Star® protective layer. Its tenacious adhesive bond to asphalt bitumen on the bottom side also becomes a barrier to asphalt to prevent discoloring the finish coat. The strong chemical affinity of Bondit to Topps Seal on the top is inseparable, making the system complete. Bondit dries in as little as 2 hours for quick project completion.

TS Commercial Grade™

Topps Seal Commercial Grade™ is an alternative elastomeric, water-free cool white roof coating exceeds the physical properties of most all competitive coatings at a very economical price for your industrial or commercial roof projects. It provides all-weather, seam-free protection that repels moisture and keeps harmful UV rays off your roof. The superior moisture resistance properties of TS Commercial Grade™ guard to prevent rust on metal and provides a durable and effective shield against weathering. The water-free package gives installers an extended application season, without threat of freezing, and with reduced wash-off risks.

RustArrestor™ [for Metal Roofs]

A package of two powerful cleaners simultaneously neutralize and dissolve surface rust as it stabilizes oxidation for coating with Topps Seal® water-free coatings. Applies by pump-up sprayer or rag mop at approximately 0.15 liters per square meter, followed by power wash after just 10 minutes. May be repeated if needed for heavy rust. In cases of heavier rust, allow to sit up to 30 minutes prior to power washing.

ClearSeal™ [for Asbestos & Concrete Roofs]

This penetrating clear thin primer prepares porous non-painted masonry and concrete for sealing with Topps Seal® and other coatings. ClearSeal absorbs and bonds light surface oxidation and forms an initial seal beneath the surface. Prepares oxidized surfaces so they may be coated over with excellent adhesion.

Bondit™ [for Bitumen Roofs]

Bondit allows for instant compatibility of Topps Seal® solvent based products over stable black bituminous systems for resurfacing them with rubber durability and the Topps Seal Energy Star® protective layer. Its tenacious adhesive bond to asphalt bitumen on the bottom side also becomes a barrier to asphalt to prevent discoloring the finish coat. The strong chemical affinity of Bondit to Topps Seal on the top is inseparable, making the system complete. Bondit dries in as little as 2 hours for quick project completion.

Topps Seal®

When sealing a commercial or industrial roof, look no further than Topps Seal® for the best protection available. Topps Seal® is the flagship of the Topps® protective roof maintenance coating line, utilizing the Topps’ exclusively formulated 100% synthetic thermoplastic technology.

The extraordinary features of Topps Seal® make it the most widely recognized protective maintenance roof coating now in use on all continents and in all climates. The combination of high elongation and superior strength allow Topps Seal® to withstand challenging thermal changes and inclement weather. The seal also provides excellent weathering with extreme resistance to moisture and transmission.

RustArrestor™ [for Metal Roofs]

A package of two powerful cleaners simultaneously neutralize and dissolve surface rust as it stabilizes oxidation for coating with Topps Seal® water-free coatings. Applies by pump-up sprayer or rag mop at approximately 0.15 liters per square meter, followed by power wash after just 10 minutes. May be repeated if needed for heavy rust. In cases of heavier rust, allow to sit up to 30 minutes prior to power washing.

ClearSeal™ [for Asbestos & Concrete Roofs]

This penetrating clear thin primer prepares porous non-painted masonry and concrete for sealing with Topps Seal® and other coatings. ClearSeal absorbs and bonds light surface oxidation and forms an initial seal beneath the surface. Prepares oxidized surfaces so they may be coated over with excellent adhesion.

Bondit™ [for Bitumen Roofs]

Bondit allows for instant compatibility of Topps Seal® solvent based products over stable black bituminous systems for resurfacing them with rubber durability and the Topps Seal Energy Star® protective layer. Its tenacious adhesive bond to asphalt bitumen on the bottom side also becomes a barrier to asphalt to prevent discoloring the finish coat. The strong chemical affinity of Bondit to Topps Seal on the top is inseparable, making the system complete. Bondit dries in as little as 2 hours for quick project completion.

Topps Seal® Excel

Topps Seal® Excel represents the ultimate ENERGY STAR®, high performance protective maintenance roof coating. It utilizes Topps’ exclusive 100% synthetic thermoplastic technology and environmental barrier. Resin rich Topps Seal® Excel has all of the characteristics of standard-grade Topps Seal®, along with accelerated physical properties that exceed 1000% elongation and an ultimate tensile strength of 2250 psi. It retains ENERGY STAR® standards even after aging, which exceeds standards for new coating performance.

Topps Seal® Excel is used across all continents, including the Antarctic. It can be used on Metal, Modified Bitumen, BUR, PUF, Concrete, and EPDM roofs.

RustArrestor™ [for Metal Roofs]

A package of two powerful cleaners simultaneously neutralize and dissolve surface rust as it stabilizes oxidation for coating with Topps Seal® water-free coatings. Applies by pump-up sprayer or rag mop at approximately 0.15 liters per square meter, followed by power wash after just 10 minutes. May be repeated if needed for heavy rust. In cases of heavier rust, allow to sit up to 30 minutes prior to power washing.

ClearSeal™ [for Asbestos & Concrete Roofs]

This penetrating clear thin primer prepares porous non-painted masonry and concrete for sealing with Topps Seal® and other coatings. ClearSeal absorbs and bonds light surface oxidation and forms an initial seal beneath the surface. Prepares oxidized surfaces so they may be coated over with excellent adhesion.

Bondit™ [for Bitumen Roofs]

Bondit allows for instant compatibility of Topps Seal® solvent based products over stable black bituminous systems for resurfacing them with rubber durability and the Topps Seal Energy Star® protective layer. Its tenacious adhesive bond to asphalt bitumen on the bottom side also becomes a barrier to asphalt to prevent discoloring the finish coat. The strong chemical affinity of Bondit to Topps Seal on the top is inseparable, making the system complete. Bondit dries in as little as 2 hours for quick project completion.